an affordable iPhone is up there with the craziest. Today we're going to pop the lid,

tear it down, and see what that proprietary taptic engine looks like from the inside.

It should be interesting.

Let's get started.

[Intro]

Like all the iPhones in the past 9 years, there are 2 pentalobe screws down at the bottom.

The star shaped pentalobe screws are super common, so I'll link a tool kit that I use

down in the video description. This iPhone is ip67 water-resistant, all while only costing

$399. The screws even have a little black gasket under the head to help keep water out.

Heat helps with getting the screen off the iPhone SE. There is a bead of sealant around

the opening that will also help keep liquid out of the phone. Once it's warmed up I can

use a large suction cup to lift up on the bottom edge, while popping it open with my

razor blade. Taking special care, of course, not to put too much pressure on the metal

frame because we'd hate to scratch it or anything.

The top of the phone needs to come down ever so slightly before the whole thing can fold

open like a book. I'm taking special care not to put any stress on those ribbon cables

along the right hand side because they can tear just like paper...and, well, if you think

this thing looks familiar, you're right. Pretty much all of the internal components of the

2020 iPhone SE are interchangeable with the iPhone 8, like the speakers, rear camera,

and according to iFixit, even the screens are interchangeable. The battery however,

while the same size and capacity as the iPhone 8, is not interchangeable The connector's

different.

Hidden under this metal plate with the 4 screws is the battery Lego-style connector. I can

pop that off with my plastic pry tool and then work my way up to the top metal plate

and it's 3 screws. Nearly every screw in this phone is a different size and shape and requires

4 different screwdriver heads to take apart. After the 2 protective plates are gone, I

can pop off the three screen ribbon cables just like 3 little Legos. One thing I am happy

about though is that the screen is the first thing to come off on the phone. And even better,

the iPhone 8 replacement screens are currently selling for about $25 or $30 right now. So

if they really are interchangeable, it's one of the cheapest third party screen repairs

of all time. Today though, we're going to keep focused on that vibrator.

First let's get this battery out.

Another thumbs up to Apple is their magical battery pull tabs. Some manufacturers make

battery replacements impossible by gluing their batteries permanently into the phone.

I don't want to name any names, but it rhymes with Samsung. Batteries don't last forever.

I'm glad we can get this one out without exploding anything. Even if the battery pull tabs do

break sometimes.

This battery's a rather tiny 1,821 milliamp hour. Now that we have the battery out, we

can see that the internal frame of the phone is metal. And as we know, metal isn't very

see-through which makes a transparent iPhone SE pretty difficult. What we did for the Teardown

Skin was mirror the internal image so that when looked at from behind, everything lines

up exactly where it should be inside the phone. And of course, I might be a bit biased, but

I think it turned out pretty darn good. We even ripped off the metal plate covering the

A13 processor so we could see the brains of the operation. I'll leave a link for my Teardown

Skin from dbrand down in the video description. We already cover most of the new phones and

just added the iPhone 8 and iPhone 7.

One place where this phone does sacrifice a bit though is with the camera. There's only

one. While most phones nowadays are shipping with 2, 3, or even more perspectives than

that.

After pulling away the two screws and metal bracket, the rear camera comes loose. It's

a 12 megapixel unit and does have optical image stabilization. I'll pull the SIM card

tray out next and unclip 3 more ribbon cables down here by the motherboard...just like little

Legos. Apple's actually doing a pretty good job when it comes to the whole saving the

planet thing. A lot of the components inside of this iPhone SE are made from recycled materials.

For example, this motherboard, which is held in place by 10 screws, is assembled with 100%

recycled tin in the solder. Apple does still like to be difficult though with 2 more random

screws up here in the top that screw directly into the frame. I don't know what this thing

does but it's probably important.

After one more little ribbon cable connector, the motherboard comes free. And as always,

even though this phone is water resistant, there are still water damage indicators inside

that'll tattle on you if they ever get wet. No phone is waterproof and these stickers

will turn pink if the phone senses any moisture internally. And here is the motherboard, with

the same footprint as the iPhone 8. It has upgraded chips to still be relevant in 2020.

Now that the motherboard is out, we can see more of the metal backing, along with the

wireless charging coil in the center, and the long charging port ribbon that's tucked

up underneath the motherboard with it's 11 different sized and shaped screws holding

it in place.

I can remove this small metal plate and keep it organized right next to the screws that

it came out with. And now we get a good look at the loudspeaker. For a company who hates

people getting inside of their own phones, they sure plaster their logo everywhere. You

might have noticed the difference between most Androids and iPhones. Androids do tend

to be a little more consolidated with less parts and screws inside. While iPhones have

a lot more little parts, brackets, and screws all in a very specific order to remove.

Finally though, it's time to take a look at this taptic engine. So haptic feedback is

the way your phone communicates with you through vibrations. Normal vibrators that have a lopsided

spiny bit to cause vibrations are called eccentric rotating mass vibrators. But Apple was disappointed

in the split second it takes for a motor to spin up before it gets to full vibration capacity

so they invented this guy: the taptic engine, which has no rotating bits.

Peeling off the top of this electric sardine can, we can see that there are coiled copper

wires, magnets in the middle, and metal springs on either end to cushion it's back and forth

movement, along with quite a bit of oil. Which probably acts as the vibrator's internal lubricant.

Apple says that this linear actuator is able to hit full power much quicker than the rotating

mass vibrators found in other phones, which gives it more abilities. Instead of one power

level, you know, on or off, this guy's copper coils allow a range of different levels of

haptic feedback and can provide it instantly.

Personally I think it's a little overkill, but Apple apparently feels very strongly about

good vibrations. Apple also feels strongly about a complicated assembly apparently, with

two more small screws drilled directly into the bottom of the frame.

Getting a closer look at the water proofing inside of the phone, we see that the mesh

for the bottom holes is actually pretty thick. It's like a whole filter instead of just one

mesh screen. The red lightning charging port is capable of charging at 18 watts, if you

buy your own charger. And does have a white rubber ring around the tip to help keep water

out.

Another good thing that Apple is doing, before I jump into some of the bad things, is that

for the metal frame, Apple is prioritizing aluminum that is smelted using hydroelectricity

rather than aluminum that is melted with fossil fuels. Unfortunately though, after all that

effort to be green, Apple went and used permanent adhesive again on the back glass making it

impossible for the average person to replace. And apple charges $269 to replace the back

glass themselves, which is more than half the price of the phone, and completely unnecessary.

Of course, where there's a will there's a way, and there's actually some really cool

laser separator technology that let's third party repair shops replace the back glass

cheaper. I'll link the laser video down in the video description. Apparently, Apple has

a really cool machine of their own called Daisy that can tear down and recycle up to

200 devices an hour. Let me know down in the comments if you think Apple should let us

come take a closer look at that thing. Personally, I'm glad that Apple is using their old phone

designs with upgraded hardware. Phones are getting way too expensive these days and it's

nice to see a phone this good with both water-resistance and wireless charging all for less that $400.

At this price point, I bet that Apple is definitely going to steal away some Android users, and

after a few more innocent purchases like Air Pods and an Apple Water, they'll never be

able to escape. It's a slippery slope.

Finally, with the screen connected and battery in place, the phone is able to turn on. I'll

get the metal plates back in place to help keep the connections from popping off. And

even without that taptic engine inside, the phone still turns on and functions like normal.

Kind of cool. I'm curious though, if you're an Android user, does this phone tempt you

into switching sides? Let me know down in the comments.

I'll leave a link for my Teardown Skin down in the video description so you can have all

the cool bits from the inside shown off on the outside. Come hang out with me on Instagram

and Twitter. Hit that subscribe button if you haven't already. And thanks a ton for

watching. I'll see you around.