to build their planes. The Wright Brothers worked tirelessly to reduce the weight of

their aircraft to allow it get off the ground. They used woods with high strength to weight

ratios like spruce and ash to build their frame, but it needed to be reinforced with

steel wire to prevent the frame from bending under flight loads. The flight surfaces were

covered in lightweight fabric to provide a smooth aerodynamic surface. But one of their

greatest innovations was the construction of their engine. No engine existed at this

time that matched their power to weight requirements, so they went about inventing their own.

They were the first in history to use Aluminium as a building material for an engine, using

it to construct their crankcase. They even painted the engine black, so their competitors

couldn't see that the engine was built using aluminium.

Aluminium makes up 8% of the earth's crust. Despite that, it used to be one of the world's

most expensive materials. It is a difficult material to refine. Napoleon had envisioned

the lightweight metal as the perfect material for weapons and armour, but became frustrated

with the difficulty of the refining process. Finally giving up, he had his small supply

of aluminium melted down and made into cutlery and plates to serve his most esteemed guests,

while the lower ranks were resigned to the less expensive Gold pieces.

It wasn't until the 1880s that methods capable of mass producing the material were developed.

In a few short years, aluminium went from being the most expensive metal on Earth to

one of the cheapest. Dropping in price from $1200 per kilo in 1852 to just one dollar

per kilo at the start of the 20th century. This paved the way for the Wright Brothers

to use the material in the Wright Flyer, but the material the Wrights used was very different

to the Aluminium alloys we see today. Despite the availability of aluminium, planes throughout

world war 1 continued to use wood and canvas as their primary building materials, because

the aluminium that was available back then, was a weak and malleable.

An accidental discovery of a new heat treatment by the German scientist Alfred Wilm led to

the development of an aluminium alloy strong enough for structural use. Alfred was trying

to recreate the effects of quench hardening that is seen with iron alloys like steel,

you see this process a lot in the awesome Man at Arms series, after heating the steel

between 700 and 900 degrees they will quench the blade in oil or water, this rapidly cools

the steel, which causes a crystalline structure called martensite to form, which is much harder

than the crystal structure that would form if it was allowed to cool slowly. But this

technique does not work with aluminium.

As the story goes, one Friday afternoon Alfred was testing a new alloy of aluminium he had

developed, containing about 4% copper. He followed the steps for quench hardening. He

heated the metal up and allowed the heat to evenly distributed throughout the material,

he then removed the metal from the heat and quenched it, rapidly cooling it. He then tested

the material, but it showed no real sign of improvement. Becoming frustrated he left the

lab, leaving the remaining samples, resting at room temperature over the weekend.

To his amazement, when he returned the following Monday he discovered the remaining samples

had grown stronger. Alfred Wilm had just accidentally discovered age hardening. A process that would

make aluminium the world's new wonder material.

So what happened here, why did the new alloy get stronger over time? To understand this

we need to look at the metal's crystalline structure.

This is a single aluminium atom. Now if it is joined by more atoms they don't just arrange

randomly, they form regular patterns with a repeating structure. Aluminum forms a repeating

crystal structure called face centred cubic which looks like this and it defines many

of the properties of the material. One of these properties is direction it most easily

deforms, for example this crystal structure deforms most easily along this plane. This

is called a slip plane.

Let's look at a 2D cubic structure like this, it can easily slip in these parallel

directions, so if a force is applied here with sufficient force each atom will shift

down and the material will permanently deform, but this material is pure aluminium. What

happens when we swap some of these aluminium atoms for copper.

Copper atoms are slightly larger than aluminium and they create internal strain when fitting

into aluminium crystal lattice. When the alloy was heated, the copper spread evenly through

the material and the quenching process trapped the copper in these locations. In these positions,

the copper atoms do not provide much strength. But over time they begin to coalesce to form

these secondary crystal structures within the main crystal structure, this is a called

a second phase. These second phase particles create barriers to deformation, for deformation

to occur a much greater force is needed.

In the following years Alfred perfected this process, figuring out the ideal aging temperature

and time. He dubbed his new material Duralumin and it was used to build the world's first

all metal aircraft the Junkers J1.

The impact of this age hardened aluminium had cannot be understated, it completely transformed

our world. Prior to its introduction , planes frames were all built with rigid truss structures,

like this. With aluminium at their disposal, engineers could create a new type of flight

structure, the monocoque and semi-monocoque. With these frames the aluminium skin forms

an integral part of the planes strength, not just being used as a streamlined flight surface.

These new techniques freed up space within the planes and allowed spacious passenger

planes to be developed, ushering in a new era of travel in the world.

13% of the world's aluminium is used by the energy sector, even though copper is a

better conductor, all main overhead power lines use aluminium as the conducting material.

To carry the same current as a copper wire an aluminium wire needs to 1.5 times thicker

and even then it is still two times lighter. This decreases the load on pylons and allows

the spans between them to increase dramatically. This saves vasts amount of money on construction.

23 % of aluminium is used in construction. The Empire State Building was the world's

first skyscraper to use the material extensively. It's corrosion resistance and lightness

made it the perfect material for exterior framing and roofing.

It's clear to see, without this material the world we see today would be very different

and only recently has aluminium started to see competition from composite materials like

carbon reinforced plastics, but that's a topic for another day.

Thanks for watching. This video was sponsored by the vlogbrothers. I didn't even have to

put this message at the end, but I don't believe in getting something for nothing. So please

go check out Scishows latest video, the physics of the rollercoaster and consider subscribing.

If you have any questions feel free to ask me in the comments and if you would like to

support this channel the links for my patreon, instagram, facebook and twitter accounts are

below.